Lith printing questions

Discussion in 'Alternative Processes' started by HMFriedman, Dec 18, 2011.

  1. HMFriedman

    HMFriedman Member

    Messages:
    58
    Joined:
    Mar 11, 2006
    Shooter:
    4x5 Format
    I was going pretty well with Maco Superlith (in relatively short dilutions) and Kentona before both were discontinued. I am really struggling to get back to speed using Moersch Easy Lith and Fomabrom IV. To get myself straightened out, I have a few basic questions for anyone experienced in this process:

    1. What is the shelf life of unmixed Parts A & B, in partially full containers?
    2. How long will mixed developer last in an open tray?
    3. What is the approximate capacity (8X10 prints) of 1000ml of developer at 1+18?
    4. Speaking of dilutions, Moersch alternately gives the possible range of dilutions as between 1+15 to 1+50 and 1+1+20 to 1+1+80. Am I in brain-lock, or is it so that 1+1+20 of A+B+water equals 1+10+water?

    Finally, does it make sense that a negative that prints well in Ethol LPD 1+3 when exposed for 14 seconds at f11 is still underexposed and require upwards of 25 minutes development when exposed for 90 seconds at f8? Or, is my developer cooked?

    Sorry for the lengthy post, and thanks in advance to anyone who can help me out.

    Regards,
    Henry
     
  2. MDR

    MDR Member

    Messages:
    1,411
    Joined:
    Sep 1, 2006
    Location:
    Austria
    Shooter:
    Multi Format
    Fomabrom is extremely slow in lith I use the same paper with good results and usual developing time is 25 to 30 mins after a 5mins exposure at f8 can't help you with moersch easylith as I still use the old Maco Lith chemstry myself maybe Wolfgang Moersch or Tim Rudman will chime in both are members of this site.

    cheers Dominik
     
  3. Jerevan

    Jerevan Subscriber

    Messages:
    2,031
    Joined:
    Nov 19, 2004
    Location:
    Sweden/Germany
    Shooter:
    35mm
    Okay, this is a bit of information on the way... Judging from the base exposure, you are in the ballpark for the right exposure times. If it is low on contrast, do a shorter exposure. Or longer if it needs less.

    I am doing 90 seconds at f/8, do the liths in warm developer (35-40 degrees) and get a print in 3-5 minutes with Fomabrom III at 30 A/30 B and 900 ml of water. I don't use old brown (leftover developer from the session before that you use to season the new developer bath with) but I get 4-5 prints (8x10) out of one batch. I guess my patience runs out faster than the developer brew, so I might get more out of it if I persevered. :smile:

    When I get development times upwards of 25 minutes, either my developer is exhausted or it's getting cold (towards 20 degrees). I usually start with changing the waterbath my developer tray sits in. A new trick I learned quite recently is to use the same size of tray for the water bath, then it does not cool off as quickly.

    I started out with Fomabrom and I really bloodied my nose on that combination, so I found Fomatone very easy when I used that.
     
    Last edited by a moderator: Dec 18, 2011
  4. bdial

    bdial Subscriber

    Messages:
    5,416
    Joined:
    Jan 2, 2005
    Location:
    NE U.S.
    Shooter:
    Multi Format
    I've been using Moersh master lith, and fotospeed prior to that, I haven't had any problem with the unmixed concentrates going bad. I used some of my Fotospeed a few months ago, and prior to that it had been at least 1.5 years.

    When I have it I squirt argon paint preserving gas into the bottles, but that hasn't been a regular occurance.

    As for mixed lifetime I wouldn't expect more than a couple of hours in an open tray, and maybe 5 - 8 8x10s for 1000 ml's of developer.

    Sounds like your developer may have been cooked, or else too cold. What happened prior in the session? Were you getting reasonable prints and developing times with that exposure?
     
  5. artonpaper

    artonpaper Subscriber

    Messages:
    326
    Joined:
    Aug 7, 2007
    Location:
    Staten Islan
    Shooter:
    Multi Format
    Are Foma papers still available? And if not, what are some good suggestions for someone who has little or no Foma left. I've never done lith printing, but I'm very interested in it.
     
  6. trotkiller

    trotkiller Subscriber

    Messages:
    146
    Joined:
    Feb 7, 2008
    Location:
    København
    Shooter:
    Multi Format
    Foma papers are very much still available.

    Fomatone in FB or RC is great as is the Fomabrom IV 123 mentioned in the original post

    Oriental Seagull VCFB Warmtone is the next paper I'm going to try, I have heard it is very similar to Fomatone. It also comes in boxes of 50 sheets in most sizes, my main size is 11x14 and Fomatone only comes as a 25 sheet pack.
     
  7. trotkiller

    trotkiller Subscriber

    Messages:
    146
    Joined:
    Feb 7, 2008
    Location:
    København
    Shooter:
    Multi Format
    Try using a bigger dev tray. I always use 100ml of each dev solution when making up my dev, I use 1:1:23 which gives me 2.5 L of dev. With this volume of dev you are going to get at a good number of prints before you need to replenish. I also use old brown so I hit the "sweet" zone much quicker
     
  8. Mark Fisher

    Mark Fisher Subscriber

    Messages:
    1,678
    Joined:
    Dec 13, 2003
    Location:
    Chicago
    Shooter:
    Medium Format
    Maco superlith is still available under the Rollei brand. Great stuff. Fomabrom is a difficult paper to really learn on (very gritty, strong infectous development, very slow even heated to 100F) and certainly looks very different from Kentona. I have no experience with Easylith. Try some Fomatone or Oriental warmtone and I think you'll be much happier. The other nice thing about Fomatone is that you can get many, many different looks with different toning and development.

    1:1:20 means one part A+one part B to 20 parts water.
     
  9. mooseontheloose

    mooseontheloose Subscriber

    Messages:
    2,492
    Joined:
    Sep 20, 2007
    Location:
    Kyoto, Japan
    Shooter:
    Multi Format
    Henry, what was your developer dilution and temperature? Like some others have mentioned above, I tend to develop in Moersch (easy or SE5) at higher temperatures (aroudn 30C) and at 1+1+25 or 1+1+30 dilutions. Developing times tend to be in the 4-7 minute range, and I can probably get at least 12-15 prints done before doing a small replenishment.

    As for paper, I've use almost every current (and some old) paper out there that liths, and I found Fomabrom very difficult. I was eager to try it after seeing some of the work done here on APUG by some members, but my attemps were slow, gritty, and prone to pepper fogging (in both LD20 and Aristalith). Perhaps you may want to try some other papers.

    Also, even though I know you're using Easylith, I think this information from Wolfgang's website might answer some of your questions:

    A remarkable characteristic of SE5 is that the working solution can be kept for an unusually long time which is normally not the case at all with Lith developers, they 'go off' very quickly. SE5, in contrast, can last for up to 10 hours in an open developing tray without the need for additional anti-oxidizing agents.

    Before I worked with SE5 I mostly used Easylith in 8-10 hour sessions and found that to be true as well (of course developer needed replenishment after 8-10 prints, but I could do about 20 in one long session and it was fine).
     
    Last edited by a moderator: Dec 18, 2011
  10. HMFriedman

    HMFriedman Member

    Messages:
    58
    Joined:
    Mar 11, 2006
    Shooter:
    4x5 Format
    Thanks, all, for your input!

    It sounds like I'm o.k. on my developer life, tray time and capacity, but will try increasing the temperature. I've been using the "Easy"Lith at 70 degrees. I'm also rethinking my choice of paper, having run into every characteristic described: slow, looong development times and difficult infectious development. I chose Fomabrom for its cooler tones, but might try Fomatone just to have some success. Oh, and I'm delighted to learn that Superlith is still available under another name.
     
  11. Mark Fisher

    Mark Fisher Subscriber

    Messages:
    1,678
    Joined:
    Dec 13, 2003
    Location:
    Chicago
    Shooter:
    Medium Format
    Fomatone can be cooled somewhat with selenium and drastically with gold toning. Fomatone is pretty remarkable because you can get so many different looks from with it. I'd be happy with just Fomabrom and Fomatone....I think I could coax almost any look I'd be interested in.....although I do miss Slavich already!
     
  12. orlovphoto

    orlovphoto Member

    Messages:
    41
    Joined:
    Nov 21, 2010
    Location:
    San Diego, C
    Shooter:
    Medium Format
    I think Foma is readily available from Freestyle in LA and thank god for that.

    I have only started doing lith recently but have been printing on all vintage papers that I found in the darkroom I bought in San Diego. There is an infinite supply of old paper there dating back to the 1940s - stuff like Kodak Bromesko, GAF, Agfa single ply galore, AZO, Luminos, Du Pont... crazy! The best thing about lith is that those papers that are time-fogged in normal developer work great with lith :smile: (sshhhhh...... let's keep that one a secret, right?)

    OK, so I am going to use this good note as a place to plug this little project which will expose people to all sorts of fun stuff including, but not limited to, lith: http://www.kickstarter.com/projects/351976604/the-photo-palace-bus
    Please help support this in any way you can - this one is for the greater Art Good. Spread the word and pledge if you can. Otherwise connect with us on facebook or blogspot and we'll be in your town soon enough :smile:
     
  13. Mei Leng

    Mei Leng Subscriber

    Messages:
    3
    Joined:
    Dec 30, 2010
    Location:
    Richmond, Va
    Shooter:
    35mm
    orlovphoto, does the source of vintage darkroom papers you found in a darkroom in San Diego still have any more to spare. Yes you are right about old paper that are time fogged a bit. Does OK with lith.