Making a Step Tablet at Home

Discussion in 'Darkroom Equipment' started by mandayam, Jun 18, 2011.

  1. mandayam

    mandayam Member

    Messages:
    2
    Joined:
    Jun 13, 2011
    Shooter:
    Multi Format
    Hello,

    Is there a way to make a Step Tablet myself for 4x5 negatives?
     
  2. Bill Burk

    Bill Burk Subscriber

    Messages:
    4,984
    Joined:
    Feb 9, 2010
    Shooter:
    4x5 Format
    A step wedge is such a low cost, high value photographic "instrument" that it is worth buying one rather than making one. I paid $3.75 for mine 35 years ago and though I wanted to buy two at the time money was hard to come by so I only bought one. I still have and use that strip regularly.

    If you are in a "desert island" situation and must make do with tools at hand, you could make a continuous-wedge. Later, visit someone with a densitometer and circle spots on the negative that read in .15 intervals from 0.00 to 3.00 for a 21 step scale.

    By making a continuous tone wedge and picking spots, you will have a better chance of finding spots on the negative that are the correct densities. If you tried to make steps, there would be many mis-steps even if you work to high standards.
     
  3. ic-racer

    ic-racer Member

    Messages:
    7,470
    Joined:
    Feb 25, 2007
    Location:
    Midwest USA
    Shooter:
    Multi Format
    Use Lith film and do an exposure under the enlarger of increments increasing in exposure time. You will have to do the math, but one way would be to expose for 10 seconds then start covering in steps and expose for 4 seconds, the 6 seconds then 8 seconds then 12 seconds. That will give you the series 10, 14, 20, 28, 40 seconds. You will have to use some trial and error. When you get one sheet of film that looks good, read off the densities just as you would an uncalibrated strip you bought.
     
  4. michaelbsc

    michaelbsc Member

    Messages:
    2,106
    Joined:
    Dec 18, 2007
    Location:
    South Caroli
    Shooter:
    Multi Format
    I don't know. Seems like a lot of work for something that's actually pretty cheap to buy. I'm with Bill on this one. Even a calibrated one is reasonably priced. But the uncertified ones from Stoufer are just as accurate as the certified ones.
     
  5. Leigh B

    Leigh B Member

    Messages:
    1,035
    Joined:
    Jan 17, 2011
    Location:
    Maryland, US
    Shooter:
    Multi Format
    The "calibrated" Stouffer wedge differs from its "uncalibrated" sibling ONLY in the fact that they write the measured density on the cardboard sleeve.

    My calibrated ones all read within 0.05 of the marked value.
    The uncalibrated Stouffer wedges should be just as close.


    - Leigh
     
    Last edited by a moderator: Jun 19, 2011
  6. michaelbsc

    michaelbsc Member

    Messages:
    2,106
    Joined:
    Dec 18, 2007
    Location:
    South Caroli
    Shooter:
    Multi Format
    That's exactly my experience.
     
  7. Mike Wilde

    Mike Wilde Member

    Messages:
    2,936
    Joined:
    Aug 10, 2006
    Location:
    Misissauaga
    Shooter:
    Multi Format
    I agree with the stouffer supporters. I bought an uncalibrated 120 format 6x6 one a few years ago, and it was money well spent, and a most efficient organization to deal with.
    I still use the 120 step wedge on 4x5. My denistometer can read the smallish stripes this size gives when contact printed onto 4x5 film

    Just last week I made one of Ralph Lambrecht's reflection step wedges for field print tone pre-visuallization, and it took a bit of time to work out my setup.
    To try and get it done as a neg, and then worry if I was off of the toe, or over the shoulder for linearity of the film response would just not be worth it when there is a most viable commercial source.