Switch to English Language Passer en langue française Omschakelen naar Nederlandse Taal Wechseln Sie zu deutschen Sprache Passa alla lingua italiana
Members: 70,294   Posts: 1,535,496   Online: 1011
      
Page 1 of 3 123 LastLast
Results 1 to 10 of 25
  1. #1
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182

    Rollei 6000/SLX Lens Disassembly

    Looks like there is no longer any factory service available for Rollei lenses (someone correct me if I am wrong).
    I did not find much at all with an internet search for Rollei 6000/SLX lens repair information so I am posting this as a start. I think APUG has more popularity than the KYPhoto forum but maybe I'll post this there also http://www.kyphoto.com/cgi-bin/forum/discus.cgi .

    I'll show how to open up an 80mm 2.8 Planar from the front and the rear.

    From the rear:
    Mark the bayonet for re-assembly (Sarpie marker comes off with isopropyl alcohol when finished).


    Remove the silver screws around the perimeter of the bayonet ring (don't remove any of the black screws visible).

    Click image for larger version. 

Name:	file-136.jpg 
Views:	23 
Size:	164.8 KB 
ID:	73420
    Last edited by ic-racer; 08-24-2013 at 08:44 AM. Click to view previous post history.

  2. #2
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    Use correct screw driver, don't strip the heads.
    Attachment 73421

  3. #3
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    The ring comes off with wires attached at the back:
    Attachment 73422

  4. #4
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    When you lift up the back you can see an additional set of black cross-head screws. Be careful working around these wires as the sharp edge of the flange can injure the insulation when separating the barrel.
    Click image for larger version. 

Name:	file-127.jpg 
Views:	14 
Size:	157.3 KB 
ID:	73424
    Attachment 73423

  5. #5
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    After removing the screws the barrel separates. The PQ 80mm lens has one-less screw holding the assembly together.
    Attachment 73425

  6. #6
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    There are three small cross-head screw holding a plastic baffle ring on the back of the rear group of elements. Remove these screws and the ring slips off.
    Attachment 73426
    Click image for larger version. 

Name:	file-145.jpg 
Views:	16 
Size:	182.8 KB 
ID:	73430
    Attachment 73427
    Last edited by ic-racer; 08-24-2013 at 08:52 AM. Click to view previous post history.

  7. #7
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    With the plastic ring removed, you may-or-may-not be able to unscrew the rear element. In this case it came off without a lens wrench.
    Attachment 73428

  8. #8
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    This lens had an oily foggy lens surface on the rear-most group of the front elements. Easy to get to and clean in this case. The rest of the lens surfaces were OK in this case.
    Attachment 73429

  9. #9
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    Disassembly from the FRONT:
    The ring that says "Made in Germany by Rollei" will unscrew. I got this on off without a lens wrench using the rubber glove, therefore no marks.
    Attachment 73431

  10. #10
    ic-racer's Avatar
    Join Date
    Feb 2007
    Location
    Midwest USA
    Shooter
    Multi Format
    Posts
    6,182
    The screw-in ring holds the bayonet assembly in place. When removing the bayonet assembly there will be 4 small springs exposed. These springs hold tension on the bayonet locking balls around the perimeter of the front bayonet ring.
    Attachment 73432Attachment 73433

Page 1 of 3 123 LastLast


 

APUG PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Contact Us  |  Support Us!  |  Advertise  |  Site Terms  |  Archive  —   Search  |  Mobile Device Access  |  RSS  |  Facebook  |  Linkedin