Switch to English Language Passer en langue française Omschakelen naar Nederlandse Taal Wechseln Sie zu deutschen Sprache Passa alla lingua italiana
Members: 68,687   Posts: 1,482,339   Online: 880
      
Results 1 to 5 of 5
  1. #1
    Wade D's Avatar
    Join Date
    Feb 2006
    Location
    Jamul, CA
    Shooter
    Multi Format
    Posts
    877
    Images
    3

    2x3 roll film back on 4x5?

    Is it possible to adapt a 2x3 back to 4x5? I was thinking of using an old Graflex holder and putting the 2x3 back in it. I have both Graflex and Graphic backs for my Anni. I guess the biggest problem would be getting the film plane exactly where the ground glass focus would be. Any thoughts?
    Thanks for any input.

  2. #2
    Ian Grant's Avatar
    Join Date
    Aug 2004
    Location
    West Midlands, UK, and Turkey
    Shooter
    Multi Format
    Posts
    15,943
    Images
    148
    There's another thread on the same topic here.

    Yes it's possible with ingenuity, it's what I'm doing with the Graflex back I just bought off you

    Ian

  3. #3

    Join Date
    May 2007
    Location
    the Mojave desert
    Shooter
    4x5 Format
    Posts
    53

    just buy one ready made

    if you have a graplock back, graplex made them (4x5 plate with 120 roll)... or you can get a calumet (and others) that just insert into the spring back.
    Bill

  4. #4

    Join Date
    Jan 2008
    Location
    NJ
    Shooter
    4x5 Format
    Posts
    981
    Images
    3
    If you actually have a graflex back, you need the roll film holder that also fits the RB series of cameras - they're hard to find and usually expensive when you do - if you look carefully on ebay, you'll sometimes find one that's not identified (but can be spotted by carefully looking at the photo) as such and which therefore goes cheaper.

    If you have a spring back (graphic back) you need a Calumet (C-2, I believe) holder.

    If you have a Graflok back (aka International Back), there are graflex roll film holders (the older 22 & 23 and newer RH-8, 10, 12) as well as those made by other manufacturers. The Graflex ones shouldn't run more than $50.

    You could also just buy a Graflok back for your Anny - figure $75-100 - and then use the graflex made roll film holders.

    Dan

    PS - I have a roll film holder for a Graflex back that someone inexplicable (given the relative scarcity of one vs the other) hacked to make it fit into a graflok. I haven't looked at it to see if I can re-adapt it for a graflex back but it might be possible.
    Last edited by Fotoguy20d; 06-04-2010 at 08:58 AM. Click to view previous post history.

  5. #5
    Wade D's Avatar
    Join Date
    Feb 2006
    Location
    Jamul, CA
    Shooter
    Multi Format
    Posts
    877
    Images
    3
    I have 6 of the old Graflex holders with the slots on the long edge. They were bought from a fellow APUG member after I got the camera. I have since bought a Graphic spring back that fits the camera as well. So a bit of experimenting will be in order I think. Thanks for the link Ian. I looked at that yesterday and it gave me some ideas. If this works I'll post some pics.
    Last edited by Wade D; 06-05-2010 at 03:48 AM. Click to view previous post history.



 

APUG PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Contact Us  |  Support Us!  |  Advertise  |  Site Terms  |  Archive  —   Search  |  Mobile Device Access  |  RSS  |  Facebook  |  Linkedin