Switch to English Language Passer en langue française Omschakelen naar Nederlandse Taal Wechseln Sie zu deutschen Sprache Passa alla lingua italiana
Members: 70,693   Posts: 1,548,980   Online: 791
      
Results 1 to 6 of 6
  1. #1

    Join Date
    Dec 2004
    Shooter
    Medium Format
    Posts
    100

    D2 lens board alignment

    I finally got around to getting a mirror, and oidnt the hole in the mirror trick, align my d2. I had used a level in the past, but with the mirror it was still out quite a bit. The negative stage was easy.
    The problem, and my question, is how on earth do you adjust the lens boards? My 4X5 lens, on a long cone is out a little, but my shorter cone and 80mm lens are out a lot, in different directions. If they had just made the cones mount with three threaded screws instead of just two, it would make it easy.
    So what do you all do? I did a search, and couldn't find anyhting addressing the lens board, except in general terms.

  2. #2

    Join Date
    Oct 2004
    Location
    WA, USA
    Shooter
    4x5 Format
    Posts
    79
    Images
    1
    I've got a pdf copy of the Omega Technical Services Manual that I once downloaded from somewhere online; it has complete alignment, maintainence, lubrication and adjustment instructions as well as a troubleshooting chart. If you want, send me your email address in a private message and I'll forward it to you. Its 1.7mb.

  3. #3

    Join Date
    May 2003
    Location
    Northern Virginia
    Shooter
    Large Format
    Posts
    421
    Greg, I had to go public. Thank you very much for your assistance. You and this forum are the BEST.
    Jim Rhoades

  4. #4

    Join Date
    Jan 2005
    Location
    Downers Grove Illinois
    Posts
    1,052
    The manual you get will show how to get it level front to back by rotating the carriage axle.

    Left to right is easily done with a shim under the lens plate screw. Set the most used lens this way.

    Others will need shims front or rear in addition. I use tape in layers.

  5. #5
    mmcclellan's Avatar
    Join Date
    Apr 2005
    Location
    Ann Arbor, Michigan (USA)
    Shooter
    4x5 Format
    Posts
    463
    Bruce,

    I picked up a gorgeous D2 off of eBay a few months ago and had to align it. The easiest thing I found I could do is to buy a Beseler "lens align" kit from Calumet or any other Beseler dealer and then mount that on the bottom of the cone. A trip to the hardware store, some super glue, a couple of screws, and it was mounted tight and for life.

    With the lens then mounted on to that Beseler board, you can easily check and adjust your alignment at any time and fit it fast by adjusting the three allen-wrench screws. Now, whenever I need to print, first thing I do is check the alignment with a grain magnifier on the first neg and after about 30 seconds of checking and making a tiny adjustment here and there, I'm good to go!
    Michael McClellan
    Documentary Photographer
    Ann Arbor, Michigan
    http://www.MichaelMcClellan.com

  6. #6

    Join Date
    Dec 2004
    Shooter
    Medium Format
    Posts
    100
    The beselar kit looks like the way to go. The way the enalarger is designed you can get everything aligned except that last part where the lens mounts to the board.
    Thank you all for your help.



 

APUG PARTNERS EQUALLY FUNDING OUR COMMUNITY:



Contact Us  |  Support Us!  |  Advertise  |  Site Terms  |  Archive  —   Search  |  Mobile Device Access  |  RSS  |  Facebook  |  Linkedin