Has the film been x-rayed?
Has the film been x-rayed?
So load the film onto the take up spool as normal but don't close back instead zip the film and camera into a changing bag with a pencil.
You then need to wind on the film until you are sure you have got past frame 1 in the dark then mark the left edge of the frame and the right edge of the frame on the backing paper and close the back.
Remove the camera from the bag leave it outside for a minute or two put it back I bag and wind on several frames mark with pencil as before. Remove from bag take a shot put back in bag wind to end remove camera from bag unload film and soup as normal keep backing paper to align backing paper with negative strip.
If you have no fogging then it may be a artifice of winding on.
If you have fogging then it should be easy to identify were it is occurring in the camera by aligning the exposed frame and the paper and the camera.
You don't have to do this exactly you can vary it the pencil marks and a single exposed frame are the key. But make notes of what you intend to do.
i'm emphatic because this can not be fogging. At least, not fogging through his camera or film holder.
Look, there's a whole picture on the piece of film. I presume the rest of the roll has finished pictures as well, all with this VERY evenly spaced banding of over- and under-exposure, the banding reaching to the edge of the film.
You're right, it didn't come through the film gate from the lens, but how could it have come through winding the film? Do you, does anyone, wind a frame of film 10-evenly spaced distances for each frame?
So, by elimination of the impossible, the only thing left (thanks sherlock holmes) however seemingly improbably must be the answer. The bands were on the film before he shot it, or occurred during processing, not exposure.
I keep saying -- shoot another roll, see what happens.
The roll was processed along with another from a TLR in 1:100 Rodinal for over an hour without any problems (other than an instance of double exposure, and evidence the slow speeds are off below 1/60th intermitantly).
Still foxed by the cause, but I'll be putting another roll through it, and the other back, that was delivered today as hopefully the chances of two backs having the exact same problem are relativley low. . .
Any suggestions on the best supplier for repair parts and velvet light-trap material - I received a sheet of light-trap felt and in this case for the potential repair work that may be needed, I'm a little dubious. . .
I take it that as you have referred to another poster in the U.K. as being on the "right island" and asked for a repairer that you too are U.K. based. If so then I can think of two good repairers, neither of whom will be cheap.
Newton and Ellis in Liverpool and Ed Trzoska in Leicester or Leicestershire. I don't have their website links but google both names and you can at least speak to them.
There are others. Google will no doubt give you previous threads from APUG as well. It usually throws the kitchen sink at you when you google
I think it is some combination of a winding problem and a light leak - I would run a roll through the holder with all shots taken with a lens cap on. See if you see "waves" of fogging.
On my phone it looks more like fogging even the variation in density...
Can you look again please.
So rather surprisingly, the newer back arrived from France (Posted Saturday and arrived Thursday. . . while Royal Mail takes the same time to deliver a small packet from 60 miles away . . . ) It should help diagnose the problem - if it works, and the older one still produces problems, then I Know its the back. If the new one produces similar, then it's somewhere where the on the body where it meets the back. I'll keep you posted, just building an order for http://ag-photographic.co.uk/
I agree, it's impossible that this is fogging. I too have never seen anything like it. It looks like a test strip on a darkroom print. It certainly has nothing to do w/ the red window....you don't even need anything back there, as 120 film has backing paper. I've pried the red windows out of many old folders when they got so dark w/ age that I could not see the film numbers through them, and simply had an open hole back there (w/ a bit of black tape over it when I wasn't checking it). No issues whatsoever.
Maybe there's a light leak somewhere, and that's the creases in the bellows folds we're seeing.